Types of modern cement

Portland cement blends

Portland cement blends are often available as inter-ground mixtures from cement producers, but similar formulations are often also mixed from the ground components at the concrete mixing plant.[35] Portland blastfurnace cement contains up to 70% ground granulated blast furnace slag, with the rest Portland clinker and a little gypsum. All compositions produce high ultimate strength, but as slag content is increased, early strength is reduced, while sulfate resistance increases and heat evolution diminishes. Used as an economic alternative to Portland sulfate-resisting and low-heat cements.Portland flyash cement contains up to 35% fly ash. The fly ash is pozzolanic, so that ultimate strength is maintained. Because fly ash addition allows a lower concrete water content, early strength can also be maintained. Where good quality cheap fly ash is available, this can be an economic alternative to ordinary Portland cement Portland pozzolan cement includes fly ash cement, since fly ash is a pozzolan, but also includes cements made from other natural or artificial pozzolans. In countries where volcanic ashes are available (e.g. Italy, Chile, Mexico, the Philippines) these cements are often the most common form in use.. High Temperature Insulation  Portland silica fume cement. Addition of silica fume can yield exceptionally high strengths, and cements containing 5–20% silica fume are occasionally produced.

However, silica fume is more usually added to Portland cement at the concrete mixer. Masonry cements are used for preparing bricklaying mortars and stuccos, and must not be used in concrete. They are usually complex proprietary formulations containing Portland clinker and a number of other ingredients that may include limestone, hydrated lime, air entrainers, retarders, waterproofers and coloring agents. They are formulated to yield workable mortars that allow rapid and consistent masonry work. Subtle variations of Masonry cement in the US are Plastic Cements and Stucco Cements. These are designed to produce controlled bond with masonry blocks. Expansive cements contain, in addition to Portland clinker, expansive clinkers (usually sulfoaluminate clinkers), and are designed to offset the effects of drying shrinkage that is normally encountered with hydraulic cements. This allows large floor slabs (up to 60 m square) to be prepared without contraction joints. White blended cements may be made using white clinker and white supplementary materials such as high-purity metakaolin. Colored cements are used for decorative purposes.
High Temperature Cement

In some standards, the addition of pigments to produce "colored Portland cement" is allowed. In other standards (e.g. ASTM), pigments are not allowed constituents of Portland cement, and colored cements are sold as "blended hydraulic cements". Very finely ground cements are made from mixtures of cement with sand or with slag or other pozzolan type minerals that are extremely finely ground together. Such cements can have the same physical characteristics as normal cement but with 50% less cement particularly due to their increased surface area for the chemical reaction. Even with intensive grinding they can use up to 50% less energy to fabricate than ordinary Portland cements.

What Is Mastic Adhesive?

Ceramic tile adhesive is mainly available in two forms: mastic and thin set. Mastic adhesive is a premixed adhesive that can be directly applied, while thin set is a powder that must be mixed and left to sit for several minutes before using. The premixed adhesive is applied in areas where moisture will not be an issue, such as backsplashes in kitchens or wall tile. Thin set is applied in bathrooms because it is moisture-resistant. It is not typically used on walls because it takes longer to bond.

Mastic is only suitable for ceramic tile because other types, such as porcelain or marble, are porous. Over time, the adhesive could seep into the tiles and cause them to discolor. Ceramic tile is often used on walls in restaurants and homes. Mastic works well in these applications because it creates an extremely tight bond with the wall. It also sets quickly, which is an advantage when working with vertical designs because the need to stand and hold each tile while it dries is greatly reduced. High Temperature Adhesive

What Is Mastic Adhesive?

Mastic adhesive is made from the sticky resin of the mastic tree, which grows in the Mediterranean. Because of its sticky nature, it is used as a bonding agent in many commercial applications. Some types include construction adhesive, industrial adhesive, and ceramic tileadhesive. Depending on the application, the adhesive is available in thin liquid, thick glue, or paste form.

When used in construction, mastic adhesive is typically in liquid form and applied with a caulking gun. The adhesive is squeezed out by hand in a thin line along wall or ceiling joints. The strength of the adhesive helps hold load-bearing walls in place. In ceilings, the quick-setting adhesive eliminates the need to support heavy drywall for extended periods of time. Construction adhesive is also used as a temporary hold for fixtures so they can be nailed or screwed in place by one person.

Industrial uses for this adhesive include repairing duct work in the heating and air industry. This is due to its heat resistant properties and the ability to seal and form and a strong bond. The adhesive also bonds with most any material, so repairs to concrete, brick, or mortar are also possible. The adhesive for industrial uses comes in a finely ground powder that is mixed to form a paste. It is smeared onto the repair area and allowed to dry.

Masonry heater

          A masonry heater (or masonary stove, ceramic stove, tile stove) is a device for warming an interior space by capturing the heat from periodic burning of fuel (usually wood), and then radiating the heat at a fairly constant temperature for a long period . The technology has existed in different forms: from the Roman hypocaust to the Austrian/German kachelofen. The hypocaust is a system for heating the floors and walls of buildings (especiallybaths) using the smoke and exhaust of a single fire. In Eastern and Northern Europe and North Asia, these kachelofens (or steinofens) evolved in many different forms and names: for example the Russian Stove/Fireplace (Russian: Русская печь), the Finnish Stove (in Finnish: pystyuuni or kaakeliuuni, "tile oven") and the Swedish Stove (in Swedish: kakelugn, "tile stove" or "contra-flow stove") associated with Carl Johan Cronstedt. The Chinese developed the same principle into their Kang bed-stove. The masonry heater has gained renewed domestic popularity recently because of its heating efficiency.


Thank for Info : http://en.wikipedia.org

Porcelain tile

          Porcelain tiles are ceramic tiles with a water absorption rate of less than 0.5 percent that are used to cover floors and walls. They can either be unglazed or glazed.

          The hardness of the tile is rated from zero to five according to the ASTM C1027 (or ISO 10545-7) test for surface abrasion resistance of glazed tile. This rating, (sometimes mistakenly called the PEI rating) determines the tiles suitability for various end use conditions.

          Large-scale production of porcelain tile is undertaken in many countries, with the major producers being China, Italy, Spain and Turkey. There are also countries undertaking small-scale production, such as Australia and strong growth in developing countries such as Brazil.

         Porcelain Tile is also a very common trend in tile installation. There are many different styles of porcelain tiles on the market and they have proved to outperform ceramic tile in durability and looks.

          It is important to note that the differences of the body of the porcelain tile, as it relates to ceramic tile, has caused many "job failures" of tile installations. Tile setters that are self trained and novices to the industry will often use cements or mastic to install the impervious body of the porcelain tile to a substrate only to have delamination occur rather quickly. Highly Modified cements are necessary for installation of this material due to the very qualities that make it such a durable long lasting decorative surface. Those specifications are determined by and dictated as industry standards by the Tile Council of America, and supported by the Tile Contractors Association.

Thank for Info : http://en.wikipedia.org

Silicon nitride

          Silicon nitride is a chemical compound of silicon and nitrogen. If powdered silicon is heated between 1300 °C and 1400 °C in an atmosphere of nitrogen, trisilicon tetranitride, Si₃N₄ is formed. The silicon sample weight increases progressively due to the chemical combination of silicon and nitrogen. Without an iron catalyst, the reaction is complete after several hours (~7), when no further weight increase due to nitrogen absorption (per gram of silicon) is detected. In addition to Si₃N₄, several other silicon nitride phases (with chemical formulas corresponding to varying degrees of nitridation/Si oxidation state) have been reported in the literature, for example, the gaseous disilicon mononitride (Si₂N); silicon mononitride (SiN), and silicon sesquinitride (Si₂N₃), each of which are stoichiometric phases. As with other refractories, the products obtained in these high-temperature syntheses depends on the reaction conditions (e.g. time, temperature, and starting materials including the reactants and container materials), as well as the mode of purification. However, the existence of the sesquinitride has since come into question.

The Si₃N₄ phase is the most chemically inert (being decomposed by dilute HF and hot H₂SO₄). It is also the most thermodynamically stable of the silicon nitrides. Hence, Si₃N₄ is the most commercially important of the silicon nitrides and is generally understood as what is being referred to where the term "silicon nitride" is used.

          Silicon nitride (i.e. Si₃N₄) is a hard ceramic having high strength over a broad temperature range, moderate thermal conductivity, low coefficient of thermal expansion, moderately high elastic modulus, and unusually high fracture toughness for a ceramic. This combination of properties leads to excellent thermal shock resistance, ability to withstand high structural loads to high temperature, and superior wear resistance. Silicon nitride is mostly used in high-endurance and high-temperature applications, such as gas turbines, car engine parts, bearings and metal working and cutting tools. Silicon nitride bearings are used in the main engines of the NASA's Space shuttles. Thin silicon nitride films are a popular insulating layer in silicon-based electronics and silicon nitride cantilevers are the sensing parts of atomic force microscopes.

Thank for Info : http://en.wikipedia.org

Pressure-sensitive adhesive

          Pressure sensitive adhesive (PSA, self adhesive, self stick adhesive) is adhesive which forms bond when pressure is applied to marry the adhesive with the adherend. No solvent, water, or heat is needed to activate the adhesive. It is used in pressure sensitive tapes, labels, note pads, automobile trim, and a wide variety of other products.

          As the name "pressure sensitive" indicates, the degree of bond is influenced by the amount of pressure which is used to apply the adhesive to the surface.

          Surface factors such as smoothness, surface energy, removal of contaminants, etc. are also important to proper bonding.

          PSAs are usually designed to form a bond and hold properly at room temperatures. PSAs typically reduce or lose their tack at low temperatures and reduce their shear holding ability at high temperatures; special adhesives are made to function at high or low temperatures. It is important to choose an adhesive formulation which is designed for its intended use conditions.

Thank for Info : http://en.wikipedia.org

Refractory

          A fire brick, firebrick, or refractory brick is a block of refractory ceramic material used in lining furnaces, kilns, fireboxes, and fireplaces. A refractory brick is built primarily to withstand high temperature, but will also usually have a low thermal conductivity for greater energy efficiency. Usually dense firebricks are used in applications with extreme mechanical, chemical, or thermal stresses, such as the inside of a wood-fired kiln or a furnace, which is subject to abrasion from wood, fluxing from ash or slag, and high temperatures. In other, less harsh situations, such as in an electric or natural gas fired kiln, more porous bricks, commonly known as "kiln bricks" are a better choice. They are weaker, but they are much lighter, easier to form, and insulate far better than dense bricks. In any case, firebricks should not spall under rapid temperature change, and their strength should hold up well during rapid temperature changes.


Thank for Info : http://en.wikipedia.org

Oil shale

Oil shale

          Oil shale, also known as kerogen shale, is an organic-rich fine-grained sedimentary rock containing kerogen (a solid mixture of organic chemical compounds) from which liquid hydrocarbons called shale oil (not to be confused with tight oil—crude oil occurring naturally in shales) can be produced. Shale oil is a substitute for conventional crude oil; however, extracting shale oil from oil shale is more costly than the production of conventional crude oil both financially and in terms of its environmental impact. Deposits of oil shale occur around the world, including major deposits in the United States of America. Estimates of global deposits range from 2.8 to 3.3 trillion barrels (450×10⁹ to 520×10⁹ m³) of recoverable oil.

          Heating oil shale to a sufficiently high temperature causes the chemical process of pyrolysis to yield a vapor. Upon cooling the vapor, the liquid shale oil—an unconventional oil—is separated from combustible oil-shale gas (the term shale gas can also refer to gas occurring naturally in shales). Oil shale can also be burnt directly in furnaces as a low-grade fuel for power generation and district heating or used as a raw material in chemical and construction-materials processing.

          Oil shale gains attention as a potential abundant source of oil whenever the price of crude oil rises. At the same time, oil-shale mining and processing raise a number of environmental concerns, such as land use, waste disposal, water use, waste-water management, greenhouse-gas emissions and air pollution. Estonia and China have well-established oil shale industries, and Brazil, Germany, Russia also utilize oil shale.

          Oil shales differ from oil-bearing shales, shale deposits which contain petroleum (tight oil) that is sometimes produced from drilled wells. Examples of oil-bearing shales are the Bakken Formation, Pierre Shale, Niobrara Formation, and Eagle Ford Formation.

Thank for Info : http://en.wikipedia.org

Refractory anchorage

          All refractory require anchorage systems such as wire formed anchors, formed metal (for example, hexmetal) or ceramic tiles to support the refractory linings. The anchorage used for refractory on roofs and vertical walls are more critical as they must remain able to support the weight of refractory even at the elevated temperatures and operating conditions.

          The commonly used anchorages have circular or rectangular cross-section. Circular cross-section are used for low thickness refractory and they support less weight per unit area; whereas the rectangular cross-section is used for high thickness refractory and can support higher weight of refractory per unit area. The number of anchors to be used depend on the operating conditions and the refractory materials. The choice of anchors material, shape, numbers and size has significant impact on the useful life of the refractory

Thank for Info : http://en.wikipedia.org

Furnace

          A furnace is a device used for heating. The name derives from Latin fornax, oven.

In American English and Canadian English, the term furnace on its own is generally used to describe household heating systems based on a central furnace (known either as a boiler or a heater in British English), and sometimes as a synonym for kiln, a device used in the production of ceramics. InBritish English the term furnace is used exclusively to mean industrial furnaces which are used for many things, such as the extraction of metal from ore(smelting) or in oil refineries and other chemical plants, for example as the heat source for fractional distillation columns.

          The term furnace can also refer to a direct fired heater, used in boiler applications in chemical industries or for providing heat to chemical reactions for processes like cracking, and is part of the standard English names for many metallurgical furnaces worldwide.

The heat energy to fuel a furnace may be supplied directly by fuel combustion, by electricity such as the electric arc furnace, or through induction heatingin induction furnaces.

Thank for Info : http://en.wikipedia.org

Plastic explosive

          Plastic explosive is a specialised form of explosive material. It is a soft and hand moldable solid material. Plastic explosives are properly known as putty explosives within the field of explosives engineering. Common plastic explosives include Semtex and C-4. Plastic explosives are especially suited for explosive demolition as they can be easily formed into the best shapes for cutting structural members and have a high enough velocity of detonation and density for metal cutting work. They are generally not used for ordinary blasting as they tend to be significantly more expensive than other materials that perform just as well in that field. Also, when an explosive is combined with a plasticizer, its power is generally lower than when it is pure.


Thank for Info : http://en.wikipedia.org

Putty

          Putty is a generic term for a plastic material similar in texture to clay or dough typically used in domestic construction and repair as a sealant or filler.Painter's Putty is typically a linseed oil based product used for filling holes, minor cracks and defacements in wood only. Putties can also be madeintumescent, in which case they are used for firestopping as well as for padding of electrical outlet boxes in fire-resistance rated drywall assemblies. In the latter case, hydrates in the putty produce an endothermic reaction to mitigate heat transfer to the unexposed side.


Thank for Info : http://en.wikipedia.org